Sunday, April 29, 2012

Flame Box Elder Bowl

Just finished a sweet little, 5" diameter bowl in Flame Box Elder.  It is already promised, but I have a bit more of this wood, so stay tuned!




Sunday, April 22, 2012

Desk Clocks

I had a few pieces of showy wood I didn't know quite what to do with, and decided on these:






I think they turned out rather well, and now I'm plotting how to do more.
The top photo is Big Leaf Maple Burl, about 8" tall and 11-1/2" wide.
The bottom one is some kind of unknown Pine, with a brilliant red, flame-grained surface when oiled. It is 10" tall and 4-1/2" wide at the base.  Each has a clock face of 1-3/8", large enough to read close by on a desk top, and small enough to show off these flashy woods.

The tall pine clock is available at my Etsy website:  BarbS Woodworks
The maple burl clock is on Desk Accessories on my main website.

Friday, March 23, 2012

Oh, my aching back!

Tonight I sit with a heating pad on my back. My shop is cluttered with freshly cut turning blanks stacked helter-skelter on top of each other, with latex paint protecting the end grain of each one. Twelve and fourteen-inch blocks sit in the wheel barrow, on the bench, atop an extra chair, and sawdust from the band saw litters the floor as if the place was a circus tent.

Here is where it began: a yard tree we are sorely going to miss.  Catalpa, in winter, with no hint of its elephant-ear leaves, pyramidal white flowerette blossoms and 12-in. long bean pods. It gave us plenty of shade, lots of birds' nests, several wood peckers, and even a big horned owl one year. Yes, we'll  miss this tree. It was old. It was rotting from the inside. And it had to come down.




The tree service ground up the small stuff, and piled huge hunks of the trunk and main branches on our side lawn.  I am the proud owner of a new Peavy Hook.  It's a monster tool, and just what I needed to move these chunks around so I can get to them with my small electric chain saw.  I begin by lopping off outer parts of the edges, then cut from two sides toward center. It's a lot of labor, but it feels tremendously good to get some results before all this wood cracks beyond redemption.


Tomorrow is another day.  I need to rearrange, to make room for storage. And I'm planning on cutting some more big pieces with the chain saw.  And learning to use my Peavy Hook. And, the forecast is for a sunny, beautiful day.  Life is good.

Monday, March 19, 2012

Readers Gallery/ Woodturning Magazine

I'm honored to be included in the Reader's Gallery section of GMC Publications Woodturning Magazine in the UK, issue 236, February 2012.





Thursday, March 15, 2012

A Fun Project!

Having some fun over the last two days.  I have a few birthdays coming up, and these are really popular with the Grandkids!


Saturday, February 25, 2012

A Necessary Storage Unit

  Through the winter I've become weary of carrying adhesives into the house from my very cold shop. I have three electric heaters, but running them all trips the breaker, and running one big one only maintains the garage at about 40ºF.  I don't leave heat on all night, so our Pacific NW chills of 20ºF at night don't do my finishes any good, either.  The solution was a heated cabinet for storage of all these shop necessities.

  I started with drawings to design a tall skinny cupboard to fit an available space. I had 60" in height, 15-1/2" in width, and 10" in depth to work with.  I did a lot of scribbling and gathered some plywood and old shelving salvaged from a kitchen remodel years ago.



  I cut pieces and added in the shelves, leaving 1-1/2" open space at the back and 1" open space at the front of each shelf for air flow to carry the heat throughout the cabinet.



  Then I turned four bun feet out of oak because it would wear well against a concrete floor.




And cut foam board to lay in for insulation on all inside surfaces.  The thermostat at the top of the cabinet is wired in series with the 60 watt light bulb at the bottom, so as I set the temperature it turns the light on and off.  (Credit goes to George for helping me with this.) The light bulb is protected by a wire cage taken off an automotive trouble light so if something falls, the bulb won't be broken.




All assembled and the hinges added on.  Four small rare-earth magnets hold the door closed. I still need a knob or handle on it.  The top overhang on the right side is to store four cam clamps I have nowhere else to put.  I'll be adding some hooks on the right side for various things, too.



And here is the inside with the light on, fully insulated with foam board.

  I've photographed it outside, and will be putting it in place after testing it all night as our temperatures drop.  I have an independent thermometer to place inside for a reading.

  It's such a sense of accomplishment to complete some new shop furniture.  I love getting my storage more organized and freeing up space where all these things are scattered around, and now drawn together in one place so I know better what I have.  

  So, enough with the shop organization for now.  On to some real projects!



copyright Barb Siddiqui, use with permission only